打膠機在打膠中發生斷膠解決小妙招
在使用中空玻璃自動打膠機打膠時，在打膠過程中比較容易會發生斷膠或者直接堵塞的現象。可能是由于硅酮膠不符合行業產品質量標準，雜質過多導致堵塞。盡量使用符合行業標準的合格產品。就可以解決這類情況。
When the insulating glass automatic gluing machine is used for gluing, it is easy to break the glue or block it directly during the gluing process. It may be that the silicone glue does not meet the quality standards of the industry products, and there are too many impurities leading to blockage. Try to use qualified products that meet national industrial standards. This kind of situation can be solved.
打膠機在打膠中發生不出膠解決小妙招
The glue applicator fails to produce glue in the process of gluing. Tips for solving the problem
1、看看打膠機的氣源是否在0.6~0.8Mpa之間。
1. Check whether the air source of the glue applicator is between 0.6 and 0.8MPa.
2、檢查黑白膠開關與電磁閥是否有正常運作。
2. Check whether the black-and-white glue switch and solenoid valve operate normally.
3、檢查液壓站有沒有壓力，如果沒有壓力，也會導致不出膠的情況。
3. Check whether there is pressure in the hydraulic station. If there is no pressure, it will also lead to glue failure.
4、檢查屏顯示的編輯功能菜單中的密封不使用是否打開。
4. Check whether the seal in the edit function menu displayed on the screen is turned on when it is not in use.
5、檢查清洗時能否出白膠，如果不出白膠，檢查313膠管、旋轉接頭是否有阻塞。
5. Check whether there is white glue during cleaning. If there is no white glue, check whether 313 rubber hose and swivel joint are blocked.
Jinan two-component glue applicator has flower glue in the process of gluing, which is a clever way to solve the problem
1、看看黑膠、白膠壓力是否是保持平衡：黑膠膠泵壓力不能低于0.6Mpa、白膠膠泵壓力大概為0.4Mpa左右。
1. Check whether the pressure of black glue and white glue is balanced: the pressure of black glue pump cannot be lower than 0.6MPa, and the pressure of white glue pump is about 0.4MPa.
2、檢查一下黑膠、白膠的比例配比是否為1：10左右。
2. Check whether the proportion of black glue and white glue is about 1:10.
3、檢查看看混膠器是否安裝正確以及是否被及時清理。
3. Check whether the glue mixer is installed correctly and cleaned in time.
4、看看黑膠、白膠的智能壓力表的參數是否正常。
4. Check whether the parameters of the intelligent pressure gauge of black glue and white glue are normal.
打膠機在打膠中發生斷膠解決小妙招就是以上所講解內容了，為了之后產品的質量有所保障，就需要在平常中進行維護保養以及提前做好維護工作，更多信息的獲取就來網站
http://m.vrqf.com.cn咨詢吧。
In order to ensure the quality of products in the future, it is necessary to carry out maintenance in normal times and do maintenance work in advance. For more information, please come to the website http://m.vrqf.com.cn Consult.
上一篇：講解打膠機的安裝調試過程
下一篇：點膠機操作流程以及維護保養事項
