自動點膠機膠量控制的合理性!
在包裝工業中,控制從自動分配機分配的膠水量是一個普遍的問題。 自動點膠的施涂時間對包裝產品的質量有影響。 這也是企業中重要的問題,因此是否要避免此類問題? 今天,
濟南雙組份打膠機將與您分享以下幾點:
In the packaging industry, it is a common problem to control the amount of glue distributed from the automatic distributor. The application time of automatic dispensing has an effect on the quality of packaging products. This is also the most important issue in the enterprise, so should we avoid this kind of problem? Today, Baiqing Automation's old clocks and watches will share with you the following points:
1,點膠機的壓力設定
1. Pressure setting of dispensing machine
自動分配器為針頭或膠槍提供一定的壓力,以確保膠水的供應,而壓力決定了膠水的量和膠水的速度。 如果壓力太高,膠水將溢出并且膠水量將過多。 如果壓力太小,間歇和泄漏點可能會影響對膠水量的控制,這將導致產品缺陷。 壓力應根據膠水的性質和工作環境的溫度進行選擇。 環境溫度會降低膠水的粘度,使其更具流動性。 此時應減小壓力值,反之亦然。
The automatic distributor provides a certain pressure for the needle or rubber gun to ensure the supply of glue, which determines the amount and speed of glue. If the pressure is too high, the glue will overflow and the amount of glue will be too much. If the pressure is too low, the intermittent and leakage points may affect the control of glue volume, which will lead to product defects. The pressure should be selected according to the nature of the glue and the temperature of the working environment. Ambient temperature can reduce the viscosity of glue and make it more fluidity. At this time, the pressure value should be reduced, and vice versa.
2,點膠機的設定時間
2. Setting time of dispensing machine
根據膠量控制的工作經驗,膠點的直徑應為產品間距的一半。 這將確保有足夠的膠水粘合組件并避免過多的膠水效果,這取決于自動分配器設置的時間長度。 實際上,應根據生產條件(室溫,膠水粘度等)選擇點膠設定時間。
According to the experience of glue quantity control, the diameter of glue point should be half of the product spacing. This will ensure that there is enough glue to bind components and avoid excessive glue effects, depending on the length of time the automatic dispenser is set up. In fact, the setting time of dispensing should be selected according to the production conditions (room temperature, glue viscosity, etc.).

3,飲水機針頭尺寸
3. Drinking machine needle size
在實際工作中,針頭的內徑應約為膠合點直徑的1/2。 分配過程應基于膠水控制量和產品尺寸。 點膠頭應由不同尺寸的不同針頭制成,可以保證自動點膠機控制的膠點質量,提高生產效率。
In practice, the inner diameter of the needle should be about 1/2 of the diameter of the gluing point. Distribution process should be based on glue control and product size. The dispensing head should be made of different needles of different sizes, which can ensure the quality of the dispensing point controlled by the automatic dispensing machine and improve the production efficiency.
上一篇:自動點膠機膠體的粘度對產品的影響!
下一篇:點膠機運行過程中常存在哪些缺陷?