美女被免费网站视频九色-美女被啪到哭网站在线观看-美女被拍拍拍拍拍拍拍拍-美女被色-4438x亚洲最大-4444狠狠

你現在的位置:首頁>企業動態

雙組份打膠機的性能介紹!

瀏覽:0
  雙組份打膠機的操作
  Operation of two-component glue beater
  1、接通氣源:
  1. Connect the gas source:
  源接通,調節減壓閥0.4~0.6Mpa,檢查系統有無漏氣現象。然后試運行以下動作:(1)A泵提升;(2)A泵充氣;(3)B泵提升;(4)B泵充氣。注意:提升氣缸提升時,如果兩氣缸不同步,請下降原點后重新操作。
  The source is connected and the pressure relief valve is adjusted to 0.4~0.6 Mpa to check whether there is air leakage in the system. Then try the following actions: (1) A pump lifting; (2) A pump inflating; (3) B pump lifting; (4) B pump inflating. Note: When lifting the cylinder, if the two cylinders are not synchronized, please drop to the origin and re-operate.
  2、將A、B組份膠桶就位,并與A、B膠泵的軸線對中。
  2. Position the rubber drums of component A and B and align them with the axes of the rubber pumps of component A and B.
  以A組份為例:
  Take Component A as an example:
  1)操作手動轉閥,將A泵提升高氣動雙組份打膠機,提升過程中觀察各管路有無拉伸過緊處。
  1) Manual rotary valve is operated and pump A is lifted to the highest pneumatic two-component glue beater. During the lifting process, whether the pipelines are stretched too tight or not is observed.
  2)將膠桶放置在A泵壓膠盤下雙組份打膠機,開啟膠桶雙組份打膠機配件,將其中塑料袋外翻桶外,膠面塑料片取出。
  2) Place the rubber drum under the A pump pressure rubber disc and open the accessories of the rubber drum double component rubber drum machine. Turn the plastic bag out of the drum and take out the plastic sheet.
  3)使A泵壓盤緩慢下降,壓盤入桶時應使其與桶口對準,將壓膠盤排氣口打開雙組份打膠機,直到壓盤接觸膠面。待壓盤內氣體全部排放完并有少量膠從排氣口溢出時,即可關閉排氣閥。(提升開關保持下壓狀態)
  3) Make the pressure plate of pump A drop slowly. When the pressure plate enters the barrel, it should be aligned with the barrel mouth. How much is it to open the exhaust port of the pressure plate to the two-component glue beater until the pressure plate contacts the glue surface? When all the gas in the pressure plate is exhausted and a small amount of glue overflows from the exhaust port, the exhaust valve can be closed. (Lifting switch keeps down-voltage state)
  4)開機試打膠:將主泵氣源開關打開,按下膠槍開關,直A泵里空氣排凈槍口處出膠連續時停止。
  4) Start-up test gluing: Turn on the air source switch of the main pump and press the glue gun switch until the glue is continuously discharged from the muzzle of the air exhaust in pump A.
  用同樣的方法操作B泵。
  Operate B pump in the same way.
  4、打膠操作:
  4. Gluing operation:
  1)松開比例杠桿上的比例泵鎖緊螺釘,將比例泵內外調整所需比例。只有當A膠和B膠的配比達到正常值時,才可進行下面的操作。
  1) Loosen the locking screw of the proportional pump on the proportional lever and adjust the internal and external proportions of the proportional pump to the required proportions. Only when the ratio of A glue and B glue reaches the normal value, the following operation can be carried out.
  2)置選擇旋鈕于A、B泵開,將膠槍出口對準兩片玻璃的中縫,打開膠槍開關,以適當速度平穩地移動膠槍使玻璃槽內的雙組份膠填滿充實為佳。打膠結束時關閉膠槍。
  2) Place the selection knob on pump A and B, point the rubber gun outlet at the middle seam of the two pieces of glass, open the rubber gun switch, and move the rubber gun smoothly at an appropriate speed to fill the two-component rubber in the glass tank. Close the glue gun at the end of gluing.
  5、更換膠桶:
  5. Replacement of rubber drums:
  1)當膠桶內的膠用完時,應立即關閉A、B開關,停止打膠。
  1) When the glue in the rubber drum is used up, the A and B switches should be closed immediately and the gluing should be stopped.
濟南雙組份打膠機
  2)打開A(或B)膠泵充氣開關,選擇A(或B)膠泵提升機構為上升位置,點動旋鈕使壓盤慢慢提起,此時應注意:膠桶盡量不要離開底盤,直壓盤完全脫離膠桶時關閉A(或B)膠泵的充氣開關。3)撤出空桶,將新膠桶置于工作位置,重復第3、4、項操作。
  2) Open the inflatable switch of A (or B) rubber pump, select the lifting mechanism of A (or B) rubber pump as the ascending position, and point the knob to lift the platen slowly. At this time, it should be noted that the rubber bucket should not leave the chassis as far as possible, until the platen is completely separated from the rubber bucket, close the inflatable switch of A (or B) rubber pump. 3) Remove empty barrel, place new rubber barrel in working position, repeat operation 3, 4 and item 3.
  1、膠槍:因雙組份膠是由兩種膠混合而成的,其凝固速度與環境溫度和A、B膠的比例有關,混合后的膠一般在20分鐘之內就會反應固化。所以,當設備在正常打膠后,20分鐘之內不使用就必須將混合后的膠沖洗出來,以免堵塞混膠器和膠槍。具體操作:將B泵關閉,打開B膠回流開關然后打開膠槍,膠條為白色即可。
  1. Gun: Because two-component gum is made of two kinds of gum, its solidification speed is related to the environment temperature and the ratio of A and B gum. The mixed gum will react and solidify in 20 minutes. Therefore, when the equipment is not used within 20 minutes after normal gluing, the mixed glue must be rinsed out to avoid blocking the mixer and gun. Specific operation: Close the B pump, turn on the B glue reflux switch and turn on the glue gun until the glue strip is white.
  洗槍:
  Wash guns:
  把混合器放到水中燒,直到把混合芯拿出為;注黑把手里面還有一結。混合器和槍頭之間的旋轉部位不可燒;槍頭不可燒。可用鐵絲打通為止
  Burn the mixer in water until the mixing core is taken out; there is a knot in the black injection handle. The rotating part between the mixer and the gun head shall not be burned; the gun head shall not be burned. Till wire can be used to break through
  以上內容由雙組份打膠機整理發布,更多相關信息可以點擊我們的官網進行咨詢:http://m.vrqf.com.cn
  The above content is organized and published by two-component glue machine. More information can be consulted by clicking on our official website: http://m.vrqf.com.cn.

上一篇:打印機受潮要應該怎么處理?
下一篇:市面上的灌膠機的分類有哪些?

  • 微信
主站蜘蛛池模板: 一级毛片免费不卡在线 | 黄 片影 院 | 亚洲综合偷自成人网第页色 | 人人人干| 日本人成年视频在线观看 | 最新精品亚洲成a人在线观看 | 亚洲一区二区三区不卡视频 | 波多野结衣在线播放视频 | 日本一区二区三区四区视频 | 欧美午夜视频一区二区 | 成人免费视频网址 | 欧美三级欧美成人高清www | 中文字幕巨乱亚洲 | 一级毛片www | 免费高清毛片天天看 | 一级特黄录像播放 | 午夜成人影视 | 国产成人夜间影院在线观看 | 日本三级香港三级人妇 m | 日本成年网| 成人毛片免费 | 在线观看永久免费 | nu77亚洲综合日韩精品 | 麻豆精品在线观看 | 成人午夜免费剧场 | 国产一区二区三区四卡 | 黄视频日本 | 美国fx性欧美xxxx | 日韩国产欧美 | 欧美日韩在线亚洲国产人 | 九九热视频精品 | 精品一区 二区三区免费毛片 | 国产成人精品日本亚洲语音1 | 欧美日本视频一区 | 一级特级毛片免费 | 中文字幕精品一区二区日本大胸 | 日韩在线播放中文字幕 | 国产99热99 | 日韩精品一区二区三区在线观看l | 国产精品亚洲午夜不卡 | 青青在线视频 |